The 2016 Subaru Impreza is a compact car that offers a balance of performance, comfort, and efficiency. Maintaining the correct tire pressure is crucial for optimal handling, fuel efficiency, and tire longevity. Proper tire pressure not only enhances safety but also contributes to a smoother driving experience.
Understanding the recommended tire pressures for different trims and engines of the 2016 Subaru Impreza can help owners ensure their vehicles operate at peak performance. Below is a detailed tire pressure table that outlines the specifications for various trim levels and engine configurations.
2016 Subaru Impreza Tire Pressure
Tire Pressure Table for Different Trim/Engine
| Trim Level | Engine Type | Front Tire Pressure (PSI) | Front Tire Pressure (BAR) | Rear Tire Pressure (PSI) | Rear Tire Pressure (BAR) |
|---|---|---|---|---|---|
| Base | 2.0L 4-Cylinder | 32 | 2.2 | 32 | 2.2 |
| Premium | 2.0L 4-Cylinder | 32 | 2.2 | 32 | 2.2 |
| Sport | 2.0L 4-Cylinder | 32 | 2.2 | 32 | 2.2 |
| Limited | 2.0L 4-Cylinder | 32 | 2.2 | 32 | 2.2 |
| Sport Limited | 2.0L 4-Cylinder | 32 | 2.2 | 32 | 2.2 |
| 5-Door | 2.0L 4-Cylinder | 32 | 2.2 | 32 | 2.2 |
2016 Subaru Impreza Tire Pressure Sensor Reset
The tire pressure monitoring system (TPMS) in the 2016 Subaru Impreza is designed to alert drivers when tire pressure is too low or when there is a malfunction in the system. If the TPMS light is flashing, it indicates that there is an issue that needs attention. Resetting the tire pressure sensor is a crucial step in ensuring the system functions correctly.
Steps to Reset Tire Pressure Sensor
- Check Tire Pressures: Before resetting, ensure all tires are inflated to the recommended pressure listed in the owner’s manual or on the door jamb sticker.
- Turn on the Ignition: Insert the key and turn the ignition to the “ON” position without starting the engine.
- Press the TPMS Reset Button: Locate the TPMS reset button, typically found under the steering wheel or near the driver’s side dashboard. Press and hold the button until the TPMS light blinks three times, then release it.
- Start the Engine: Start the vehicle and allow it to run for a few minutes. The TPMS light should turn off if the reset was successful.
- Drive the Vehicle: Take the car for a short drive. If the light remains on or flashing, repeat the process or consult a professional.
Tire Pressure Monitoring System Light Troubleshooting
If the TPMS light continues to flash after following the reset procedure, further investigation is necessary. Here are common reasons for a persistent warning light:
| Issue | Description |
|---|---|
| Low Tire Pressure | One or more tires may be under-inflated. Check tire pressures and inflate as needed. |
| Faulty Sensor | A sensor may be malfunctioning. This could require replacement or recalibration. |
| Damaged Tire | A tire may have a puncture or other damage causing air loss. Inspect for visible issues. |
| Battery Issues | The battery in the TPMS sensor may be dead. Sensors typically have a limited lifespan. |
Additional Tips
- Regularly check tire pressures, especially before long trips.
- Consider having the TPMS checked during routine maintenance.
- Keep an eye on tire wear patterns, as uneven wear can indicate pressure issues.
- Replace sensors as recommended by the manufacturer, particularly when changing tires.
Importance of Maintaining Proper Tire Pressure
Maintaining the correct tire pressure is essential for the performance and safety of your vehicle. Properly inflated tires ensure optimal contact with the road, which enhances handling and stability. Under-inflated tires can lead to increased rolling resistance, resulting in reduced fuel efficiency and potential tire blowouts. Conversely, over-inflated tires can cause uneven wear and a harsher ride.
Regularly checking and adjusting tire pressure can extend the lifespan of your tires and improve overall vehicle performance. It also contributes to better fuel economy, saving you money in the long run. Here are key reasons to prioritize tire pressure maintenance:
Benefits of Proper Tire Pressure
- Improved Safety: Correct tire pressure reduces the risk of tire blowouts and enhances vehicle stability.
- Enhanced Fuel Efficiency: Well-inflated tires require less energy to roll, leading to better gas mileage.
- Longer Tire Life: Optimal pressure prevents uneven wear, extending the life of your tires.
- Better Handling: Proper inflation improves traction and handling, especially in adverse weather conditions.
How to Check Tire Pressure
Checking tire pressure is a simple task that can be done at home or at any gas station. Follow these steps to ensure your tires are correctly inflated:
- Gather Your Tools: You will need a reliable tire pressure gauge. Digital or analog gauges are both effective.
- Check When Cold: Tire pressure should be checked when the tires are cold, ideally before driving or after the car has been parked for at least three hours.
- Remove Valve Cap: Unscrew the valve cap from the tire you want to check.
- Press Gauge onto Valve: Firmly press the tire pressure gauge onto the valve stem. You should hear a brief hiss of air as the gauge takes a reading.
- Read the Pressure: Check the gauge reading. Compare it to the recommended tire pressure listed in your owner’s manual or on the driver’s side door jamb.
- Adjust as Needed: If the pressure is too low, inflate the tire to the recommended level. If it’s too high, release some air until it reaches the desired pressure.
- Replace Valve Cap: Always replace the valve cap after checking to prevent dirt and moisture from entering the valve.
Useful Tips for Tire Pressure Maintenance
- Check tire pressure at least once a month and before long trips.
- Inspect tires regularly for signs of damage, such as cracks or bulges.
- Consider investing in a tire pressure monitoring system (TPMS) for real-time monitoring.
- Rotate tires as recommended to promote even wear and maintain performance.
- Be aware of seasonal changes; tire pressure can drop in colder temperatures.
0 Comments